Welcome to NZ Autospares
The Front Windshield Wiper Washer Pump Motor offered is designed to fit various Volkswagen models, including Passat Estate, Golf Mk4, Fox, Polo, and Tiguan. Ensuring compatibility and quality.
Part Numbers: 1J6955651, 1T0955651A
Fits The Following:
VW Passat B5 B6 Estate 1998-2009
VW Golf Mk4 Hatchback 1997 - 2004
VW Golf Mk5 Hatchback Estate 2004 - 2008
VW Golf Plus 2005 - 2009
VW Fox all models all years
VW Polo Hatchback 2001 - 2018
VW Touran MK1 2003 - 2012
VW Touareg MK1 2003 - 2010
VW Lupo all models all years
VW Caddy & Caddy Maxi MUST HAVE REAR WIPER
VW Sharan MK1 2000 - 2010
VW Tiguan MK1 2007 -2017
Note: this product is currently out of stock in NZ. This listing is for stock that is due to arrive in the country. we generally only keep 1 unit in stock of each item to reduce cost of holding inventory.
Feel free to ask questions or contact us. We are able to acquire a wide range of other parts through our suppliers. With 15 years experience we can find it for you.
Can't find it here check out our Trademe Store
Installing the Front Windshield Wiper Washer Pump Motor for your VW Scirocco
Step 1: Prepare the Car
Park your VW Scirocco on a flat surface and turn off the engine. Ensure that you have easy access to the front windshield washer bottle.
Step 2: Disconnect the Battery (optional)
Although it's not always necessary, you may consider disconnecting the car's battery to avoid any electrical mishaps while working on the washer pump.
Step 3: Locate the Washer Bottle
The washer bottle is where the Front Windshield Wiper Washer Pump Motor is located. It is usually low down on the car, and you may need to access it from underneath the car or through the inner wheel arch or bumper trim.
Step 4: Gain Access
In some cases, gaining access to the washer pump may require you to partially remove the inner wheel arch or bumper trim. Use the appropriate tools to remove any screws, clips, or fasteners that hold these parts in place.
Step 5: Remove the Old Washer Pump
Locate the old washer pump, which is usually push-fitted into the washer bottle. Carefully disconnect the electrical connector attached to the pump. Then, remove the washer pipes connected to the pump. They should be either push-fitted or may have clips that you need to release.
Step 6: Install the New Washer Pump
Take the new Front Windshield Wiper Washer Pump Motor and place it in the same position where the old pump was. Ensure it is securely push-fitted into the washer bottle.
Step 7: Connect the Electrical Connector
Reconnect the electrical connector to the new washer pump. Ensure it's firmly in place.
Step 8: Reconnect the Washer Pipes
Attach the washer pipes back to the new pump. If they are tight or difficult to fit, you can use a hair dryer to warm them up, making it easier to slide them into place.
Step 9: Test the Washer Pump
Turn on your car's engine and test the new washer pump. Activate the windshield washer fluid to check if the pump is working correctly and that there are no leaks.
Step 10: Refill Washer Fluid
If the pump is functioning correctly, turn off the engine. Add new windshield washer fluid to the washer bottle. Make sure you use a good quality concentrate and avoid putting anti-freeze in the washer bottle.
Step 11: Reassemble
If you had to remove any inner wheel arch or bumper trim, reattach them securely using the appropriate fasteners.
Step 12: Final Check
Double-check all connections and components to ensure everything is in place and secure. Test the windshield washer system one more time to ensure it's working correctly.